Linux 系统双网卡绑定配置实现
作者:民工哥
这篇文章主要介绍了Linux 系统双网卡绑定配置实现,文中通过示例代码介绍的非常详细,对大家的学习或者工作具有一定的参考学习价值,需要的朋友们下面随着小编来一起学习学习吧
系统版本
[root@ ~]# cat /etc/redhat-release CentOS release 6.8 (Final) [root@ ~]# uname -r 2.6.32-642.6.1.el6.x86_64
网卡说明
eth0 192.168.1.8(服务器外网卡)
eth1
eth2
两块服务器网卡(内网)
关闭防火墙
[root@ ~]# /etc/init.d/iptables stop [root@ ~]# chkconfig iptables off
关闭selinux
[root@ ~]#setenforce 0 [root@ ~]#sed -i ‘s/SELINUX=enforcing/SELINUX=disabled/‘ /etc/selinux/config
禁用NetworkManager
[root@ ~]# /etc/init.d/NetworkManager stop Stopping NetworkManager daemon: [ OK ] [root@ ~]# chkconfig NetworkManager off [root@ ~]# /etc/init.d/network restart
编辑eth1网卡
[root@ ~]# cd /etc/sysconfig/network-scripts/ [root@ network-scripts\]# cat >ifcfg-eth1 <<EOF DEVICE=eth1 ONBOOT=yes BOOTPROTO=none USERCTL=no MASTER=bind0 EOF
编辑eth2网卡
[root@ network-scripts]# cat >ifcfg-eth2 <<EOF DEVICE=eth2 ONBOOT=yes BOOTPROTO=none USERCTL=no MASTER=bind0 EOF
编辑bind0网卡
[root@ network-scripts]# cat >ifcfg-bind0 <<EOF DEVICE=bind0 TYPE=Ethernet ONBOOT=yes BOOTPROTO=none IPADDR=10.0.0.8 NETMASK=255.255.255.0 GATEWAY=10.0.0.254 IPV6INIT=no USERCTL=no EOF
配置bond参数
[root@ network-scripts]# cat >/etc/modprobe.conf <<EOF alias bind0 bonding options bind0 miimon=100 mode=6 EOF
加入开机自启动(/etc/rc.local)
[root@ network-scripts]# cat >>/etc/rc.local <<EOF ifenslave bind0 eth1 eth2 EOF
重启网络服务
[root@LVS-2 network-scripts]# service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down interface eth2: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface bind0: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. Determining if ip address 10.0.0.8 is already in use for device bind0..[ OK ] Bringing up interface eth0: Determining if ip address 192.168.1.8 is already in use for device eth0... [ OK ] Bringing up interface eth1: RTNETLINK answers: File exists [ OK ] Bringing up interface eth2: RTNETLINK answers: File exists [ OK ]
配置使绑定立即生效
[root@LVS-2 network-scripts]# ifenslave bind0 eth1 eth2
测试联通
[root@LVS-2 network-scripts]# ping 10.0.0.8 PING 10.0.0.8 (10.0.0.8) 56(84) bytes of data. 64 bytes from 10.0.0.8: icmp_seq=1 ttl=64 time=0.089 ms 64 bytes from 10.0.0.8: icmp_seq=2 ttl=64 time=0.046 ms ^C --- 10.0.0.8 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1921ms rtt min/avg/max/mdev = 0.046/0.067/0.089/0.023 ms
此时会发现系统多一个网卡
[root@LVS-2 network-scripts]# ifconfig bind0 bind0 Link encap:Ethernet HWaddr 00:0C:29:CC:9B:5 inet addr:10.0.0.8 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fecc:9b55/64 Scope:LinkUP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:151 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11826 (11.5 KiB) TX bytes:258 (258.0 b)
到此这篇关于Linux 系统双网卡绑定配置实现的文章就介绍到这了,更多相关Linux 双网卡绑定配置内容请搜索脚本之家以前的文章或继续浏览下面的相关文章希望大家以后多多支持脚本之家!