centos把网卡名称修改为eth0的方法
作者：lxmhhy
本篇文章主要介绍了centos把网卡名称修改为eth0，小编觉得挺不错的，现在分享给大家，也给大家做个参考。一起跟随小编过来看看吧
centos 把网卡名称修改为 eth0
默认网卡名称是 eno16777736
1、修改配置文件 ifcfg-eno16777736
[root@localhost ~]# cd /etc/sysconfig/network-scripts/ [root@localhost network-scripts]# vim ifcfg-eno16777736
将 NAME 和 DEVICE 修改为 eth0
TYPE=Ethernet BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_FAILURE_FATAL=no NAME=eth0 UUID=0fea6de7-54d9-4a8d-bddc-3061678e8a0e DEVICE=eth0 ONBOOT=yes PEERDNS=yes PEERROUTES=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes
重命名该文件
mv ifcfg-eno16777736 ifcfg-eth0
2、禁用该可预测命名规则
在 grup 文件里面的 GRUB_CMDLINE_LINUX 变量添加 net.ifnames=0 biosdevname=0
[root@localhost network-scripts]# vim /etc/default/grub GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)" GRUB_DEFAULT=saved GRUB_DISABLE_SUBMENU=true GRUB_TERMINAL_OUTPUT="console" GRUB_CMDLINE_LINUX="crashkernel=auto net.ifnames=0 biosdevname=0 rhgb quiet" GRUB_DISABLE_RECOVERY="true"
运行命令重新生成GRUB配置并更新内核参数
[root@localhost network-scripts]# grub2-mkconfig -o /boot/grub2/grub.cfg Generating grub configuration file ... Found linux image: /boot/vmlinuz-3.10.0-327.el7.x86_64 Found initrd image: /boot/initramfs-3.10.0-327.el7.x86_64.img Found linux image: /boot/vmlinuz-0-rescue-692c580a413f41d8b51ddc4724500560 Found initrd image: /boot/initramfs-0-rescue-692c580a413f41d8b51ddc4724500560.img done
3、重启系统
[root@localhost network-scripts]# reboot now
查看网卡信息
[root@localhost network-scripts]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.81.128 netmask 255.255.255.0 broadcast 192.168.81.255
inet6 fe80::20c:29ff:fe5b:1a46 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:5b:1a:46 txqueuelen 1000 (Ethernet)
RX packets 474 bytes 41909 (40.9 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 266 bytes 45987 (44.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 6 bytes 564 (564.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 6 bytes 564 (564.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 00:00:00:00:00:00 txqueuelen 0 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
以上就是本文的全部内容，希望对大家的学习有所帮助，也希望大家多多支持脚本之家。